INSTRUCTION of MR-526 ELLIPTICAL TRAINER
INSTRUCTION of MR-526 ELLIPTICAL TRAINER

    INSTRUCTION of MR-526 ELLIPTICAL TRAINER

    $1,000.00
      DESCRIPTION

      MR-526

      ELLIPTICAL TRAINER

      INSTRUCTION MANUAL

      Email:service@merach.com

      Offiffifficial Website: www.merach.com

      Company: Zhejiang Yulu Electronic Technology Co., Ltd.

      Address: 298 Weiye Road, Binjiang District, Hangzhou,

      Zhejiang Province, ChinaMR-526 ELLIPTICAL TRAINER

      INSTRUCTION MANUALTable of Content as below

      Safety Instruction ................................... 2-3

      Exploded Drawing .................................... 4

      Parts List ......................................... 5-7

      Installation Steps ................................... 8-13

      Operation instruction of multifunctional sports monitor ...... 14-16

      Dear Customers,

      We want to thank you for having chosen an Elliptical trainer and wish you a lot of

      fun and success during training.

      Please note and follow the enclosed safety and assembly instructions carefully.

      If you have questions please do not hesitate to contact us.

      Support email:service@merach.com.SAFETY INSTRUCTION

      Before you start training on your home Elliptical trainer, please read the instructions

      carefully. Be sure to keep the instructions for information, in case of repair and for

      spare part delivery.

      This elliptical trainer is made for home use only and tested up to a maximum body

      weight of 330lb(150kg).

      Follow the steps of the assembly instructions carefully.

      For assembly use only suitable tools and asks for assistance with assembly if

      necessary.

      Check before the first training and every 1-2 months that all connecting elements

      are tight fitting and are in the correct condition. Replace defective components

      immediately and/or keep the equipment out of use until repair. For repairs, use only

      original parts.

      In case of repair, please ask your dealer for advice.

      Avoid the use of aggressive detergents when cleaning the home exerciser.

      Ensure that training starts only after correct assembly and inspection of the item.

      For all adjustable parts be aware of the maximum positions to which they can be

      adjusted/tightened to.

      The home exerciser is designed for adults. Please ensure that children use it only

      under the supervision of an adult.

      2■

      Ensure that those present are aware of possible hazards, e.g.

      movable parts during training.

      Consult your physician before staring with any exercise program.

      He or she can advise on the kind of training and which impact is

      suitable.

      WARNINGINCORRECT/EXCESSIVE TRAININGCAN

      CAUSE HEALTH INJURIES.

      Please follow the advice for correct training as detailed in training

      instructions.

      The load/work level can be adjusted by turning the adjustment

      knob on the handle bar stem.

      The safety level of this equipment can be maintained only

      if

      it is

      check regularly for all assembly procedure mentioned

      in

      the

      assembly instruction sheet.

      Please check regularly for the tightening knobs to notice

      any

      irregular wear.

      3EXPLODED DRAWING

      4MR-526 Components and Parts List

      No

      Product name

      Specification

      Material

      Quantity

      1

      Electronic meter

      JS-10327 outgoing line 12

      0

      M

      M

      ,

      tw

      o heartbeat outgoing line

      1

      0

      0

      M

      M

      1

      2

      Hand-held heartbeat

      sheet

      Flexible rubber

      2

      3

      Handle weld

      ∅25

      FE

      1

      4

      Cup head self-tapping

      screw

      M4*20

      BK

      2

      5

      Semi-round end cover

      ∅25

      PP

      2

      6

      Foam

      ∅25*3T*500mml

      HDR

      2

      7

      End cover

      ∅50*32 upper swing pipe with a small top ring

      PP

      2

      8

      Foam

      32*3t*570MML upper swing pipe

      HDR

      2

      9R

      Upper swing and left

      ∅32*1.5T*752MML

      FE

      1

      9L

      Upper swing right

      ∅32*1.5T*752MML

      FE

      1

      10

      Umbrella-head

      inner-hexagon screw

      M8*20 Nylonpatch 360°, 5MM handle 2 + central axis 2 +

      crank spindle 2

      Plating black

      6

      11

      Spring washer

      ∅8 pedal spindle 2 + central axis 2 + handlebar 6

      Plating black

      10

      12

      Spring washer

      8*36*3 central axis

      Plating black

      2

      13

      Nylon bush

      18.8*38 outer ring without groove

      PA+MnS2

      4

      14

      Curved washer

      8*19*1.5T upper swing pipe 4+ handlebar 6+ handle 2

      Plating black

      12

      15

      Umbrella-head

      inner-hexagon screw M8*205mm Upper swing with hexagon hole 4 + handlebar 6 Plating black

      10

      16

      Spring washer

      ∅19.5* ∅ 38*0.5

      BK

      2

      17

      Big flat head screw

      M5*12

      BK

      4

      18

      Line clamping plug

      ∅12 Hardness 55-60 degree

      PVC

      1

      19

      Nylon bush A

      19*38 outer ring with groove

      PA+MnS2

      2

      20

      Heartbeat line

      650MM

      2

      21

      Central axis

      ∅18. 8*354. 2MML extrusion tap on both sides M8*25

      UCP

      1

      22

      Umbrella-head

      inner-hexagon screw

      M10*78 part-thread lower swing pipe type A 5-leg hexagon

      hole

      Plating black

      2

      23

      Lower swing casing

      pipe

      ∅14*59

      UCP

      2

      24

      Bush

      32*14

      PA+MnS2

      4

      25L

      Lowe swing weld left

      ∅32*1.5T*580MML

      FE

      1

      25R

      Lower sw

      i

      n

      g

      w

      elding

      ri

      g

      h

      t

      ∅32*1.5T*580MML

      FE

      1

      26

      Spring washer

      10*19*2 lower swing pipe

      Plating black

      2

      27

      Nylon nut

      M10 lower swing pipe

      Plating black

      2

      28

      Bottle holder

      TC-F01

      Black

      1

      29

      Big head

      th

      r

      ea

      d

      cutting

      s

      c

      re

      w

      s

      M5*15 Bottle holder

      Electrophoresis

      black

      2

      30

      Handlebar pipe weld

      ∅60*1.5T*985MML cut 51°

      FE

      1

      31

      Upper line

      1100MML

      1

      32

      Fine tuning lower

      section

      Lower section of 1300mm outgoing line 34MM straight pipe

      screw

      1

      33

      Elliptical tube plug

      30*60 pedal tube

      PP

      2

      34L

      Pedal welding left

      30*60*1.5T*780MML Ellipse

      FE

      1

      34R

      Pedal welding right

      30*60*1.5T*780MML Ellipse

      FE

      1

      35

      Carriage bolts

      M6*50 pedal plate

      Plating black

      4

      36L

      Pedal left

      8001 All Black

      PP

      1

      36R

      Pedal right

      8001 All Black

      PP

      1

      37

      Spring washer

      6*14*2 pedal plate

      Plating black

      4

      38

      Spring washer

      ∅ 6

      Plating black

      4

      39

      Small round flower

      rotary knob

      M6 internal thread

      ABS

      4

      40

      Spring washer

      8*24*2 pedal mandrel

      Plating black

      2

      541

      Nylon powder

      ∅16.3*022.4 Crank connecting pipe

      PA+MnS2

      4

      42

      Umbrella-head

      inner-hexagon screw

      M8*50A type, tooth length 12MM

      Electrophoresis

      black

      2

      43

      Powder metallurgy

      11.5*8*15 (pedal tube)

      4

      44L

      M piece welding left

      3T, no M5 hole in the middle

      FE

      1

      44R

      M piece welding right

      3T, no M5 hole in the middle

      FE

      1

      45

      Spring washer

      8* office 16*1.5

      Plating black

      2

      46

      Nylon nut

      M8 opposite side with 14

      Plating black

      2

      47

      sprin

      g

      w

      a

      sh

      e

      r

      o

      u

      t

      -

      p

      l

      ane

      h

      e

      xa

      g

      o

      n

      a

      l

      n

      u

      t

      M10*1.25 opposite 15MM*7T magnetic control wheel

      ucp

      2

      48

      Wave spring washer

      ∅17.5*22*0.5

      BK

      1

      49

      Magnetic control wheel

      ∅250*345kg

      1

      50

      Bearing

      6000-2RS

      2

      51

      Nut

      M10*1.25 opposite 17MM*3T magnetic control wheel

      ucp

      2

      52

      Drill screw

      M5*20 Housing 2 + Sensor 1

      BK

      3

      53

      Magneti

      c

      c

      o

      n

      t

      ro

      l

      wheel

      s

      p

      in

      d

      l

      e

      M10*1.25 teeth pitch *112MM

      Blacking

      1

      54

      Chain adjuster

      BK

      2

      55

      Axis protector

      opposite side 15

      PP

      1

      56

      Sensor

      1100MML Sensor bar 25MML

      1

      57

      Spring washer

      17*22*2 Tianxin

      BK

      2

      58

      C-type buckle (jump

      ring)

      ∅15(axle 17)

      BK

      1

      59

      welded frame

      1

      60

      C type buckle

      For 10 axis

      BK

      3

      61

      Pressing wheel

      ∅37 * 20.5 L black surface double bearings(PB3851)

      1

      62

      Compression wheel

      arbor

      ∅10*42mml

      BK

      1

      63

      Magnet

      40*25*10MM

      Indication S/N

      10

      64

      Nut

      M6 opposite side 10

      ucp

      2

      65

      Double-thread screw

      ∅6 * 80 denticulate hinge on both sides M6*25

      BK

      1

      66

      Silica spring washer

      8*16*1.5

      1

      67

      Spring washer

      ∅6*14*1.5

      ucp

      3

      68

      Nylon nut

      M6 opposite side 10

      ucp

      1

      69

      Spring

      ∅1 * 12 circle taper, big head 15, small head 9, total length 60

      ucp

      1

      70

      Magnet set fixing seat

      4T

      FE

      1

      71

      Rotating mandrel

      ∅12*33.2

      ucp

      1

      72

      Spring washer

      ∅6

      ucp

      2

      73

      Umbrella-head

      inner-hexagon screw

      M6*15

      ucp

      2

      74

      Flange nut

      BK

      2

      75

      Cross welding

      FE

      2

      76

      L

      a

      rg

      e

      f

      la

      t

      h

      e

      a

      d

      self-

      ta

      p

      p

      in

      g

      s

      c

      r

      e

      w

      belt

      M4.5*15 disc

      BK

      8

      77

      Bearing

      60032RS

      2

      78

      Spring washer

      17*22*1 Tianxin

      BK

      3

      79

      Wave spring washer

      ∅17.5*22*0.5

      BK

      1

      80

      Belt pulley

      260*17.1 hole 4 holes

      Aluminium

      tray

      1

      81

      Belt

      460J6

      1

      82

      Tianxin welding

      ∅17*134MML

      FE

      1

      83

      Outer hexagonal screw

      M8*12(Tianxin)

      BK

      4

      84

      Front foot pad

      ∅60 (inner wheel)

      ABS

      2

      85

      Front foot pipe

      ∅60*1.2T*380MML

      FE

      1

      86

      Back foot pad

      ∅60 dodecagon

      ABS

      2

      87

      Hind foot pipe

      ∅60 * 1.2t * 485mml for bumping

      FE

      1

      88

      Umbrella-head

      inner-hexagon screw

      Medium carbon steel 8.8/5mm hexagonal hole in M8*70

      front and rear bottom pipe

      Plating black

      4

      89

      Crank plug

      Black hardness 55-60 °

      PVC

      2

      690

      Disc

      8509 black

      HIPS

      2

      91L

      Housing Left

      KS-8007

      ABS

      1

      91R

      Housing Right

      KS-8007

      ABS

      1

      92

      Drill screw

      M5*15 shell 6

      BK

      6

      93

      Sealing ring

      ∅60( Hardness 55-60 degrees)

      Black

      1

      94

      Ornament

      c

      o

      v

      e

      r

      of front

      p

      i

      p

      e

      KS-8007

      ABS

      1

      95

      Self-tapping screw

      M4.5*25

      BK

      6

      96

      Fine tuning upper

      section

      The upper section is 540mm and the outgoing line is 30MM

      1

      97

      Round head screw

      M5*55

      Plating

      black

      1

      98

      Curved washer

      5*16*1.5T

      Plating

      black

      1

      99

      Hexagon socket wrench

      5mm with cross

      UCP

      2

      100

      Open spanner

      10.17.14.19 heat treatment

      UCP

      1

      7Installation Steps

      Step 1

      After assembling the foot pad (86) and rear foot pipe(87)

      Fixing the front foot pipe (85) with screws, and aligning hole sites from the lower foot pipe with two carriage screws

      In the same way, Fixing the rear foot pipe(87) with screws, and aligning hole sites from the lower foot pine with

      carriage screws(88) Screwing with an Allen wrench (99).

      Step 2

      1. Firstly, inserting the front pipe ornament cover (94 ) into the handlebar stand pipe(30), and then the connecting line (31)

      is connected with the induction line (56) in the figure.

      1. Firstly, turning the fine adjustment to the maximum value (level 8). Connecting the fine-tuning wire (32) of the

      platform and fining the upper end (96). Inserting the handlebar stand pipe(30) into the platform (59).

      8Step 3 M piece installation

      Putting the M piece (44R) through the pedal core shaft (77) of the platform (59) parts, and fixing the M piece (44R) on the

      pedal core shaft (77) with the inner hexagon screw (10), cushions (11) and gasket (40). Screwing with an Allen wrench (99).

      (Note that the M pieces are divided into left (L) and right (R), which are marked on the package)

      Step 4 Installation of center shaft and lower swing

      Firstly, installing the pre-assembled (34R) + (25R) on the handlebar stand pipe (30) (firstly installing the position shown in

      the figure below), then successively penetrating into the lower swing (25R) with the central shaft (21), after that, putting

      them into the spring washer (16), penetrating into the handlebar stand pipe(30), the details are shown in the corresponding

      position. The other side can be installed as above. Finally, the two ends of the central shaft (21) are fixed with screws (10),

      cushions (11) and spring washers(12), fastening with two inner allen wrench(99).

      9Step 5 Installation of upper armrest, pedal tube and M piece

      Placing the upper armrest (9R) into the position corresponding to the lower swing (25R), and fastening the other side

      with screws (15) and spring washer(14) as in the previous step. (Refer to the following figure for installation)

      Putting the rear end of the pedal tube (34R) into the U-shaped opening of the M piece (44R), and then successively

      penetrating into the corresponding hole position with the inner hexagon screws (42), after that, screwing into inner

      hexagon screw pumps with the gasket (45) and the nylon cap (46). Locking it with an inner allen wrench (99) and an

      open end wrench (100) until it cannot be shaken. The other side is the same as the previous step.

      10Step 6 Installation of pedal plate

      Putting the pedal plate(36R) into the pedal tube (34R) and aligning its hole, then inserting into the hole corresponding of the

      pedal plate(36R) and the pedal tube (34R) in turn with the screw pump (35), then installing the plum blossom knob (39),

      spring washer (38) and spring washer (37) on the screw pump(35) and tightening them up. The other side can be installed as

      above.

      Step 7

      Locking the screws (15), the cushions (11), and the washers (14) into the driver's stand pipes(30),Other screws are operated

      in the same step, and tightening and fixing them with an Allen wrench (99). (See the figure for detailed operation)

      1112

      Step 8: Installation of kettle holder/fixed handle/electronic meter

      Firstly, removing the screws (29) from the handlebar stand pipe(30), aligning the hole and fixing the kettle holder (28)

      on the handlebar stand pipe with the screws (29) according to the figure.

      Fixing the fixed handle (3) on the handlebar stand pipe(30) with screws (10) and spring washers (14), tightening it with

      an Allen wrench (99). Passing the hand-held heartbeat line (20) into the corresponding position of the handlebar stand

      pipe(30), and fixing it with the line clamping plug (18).

      Removing the fixed screws (17) on the back of the electronic meter(1) in advance, connecting the upper flat cable (31)

      with the flat cable corresponding to the electronic meter (1), and the hand-held heartbeat line(20) with the hand-held

      heartbeat line corresponding to the electronic watch (1). In the end, fixing the electronic meter(1) on the handlebar

      stand pipe frame (31) with the previously removed screws (17). See the figure for details.

      Loading batteries into the battery box behind the electronic meter(1). Installation is done.Now, your machine is ready to use.

      Note:

      Make sure all the screws are tightened before using

      1314

      Operation instruction of multifunctional sports monitor

      VER.01

      NO.00044

      1. Instrument Function Buttons

      MODE Status Key

      ---Selecting the display window to be set or reset;

      RECOVERY/UP

      ---In the setting state, setting up the countdown interval, distance, calorie value and

      temperature (°C or °F) on the corresponding flashing window.

      ---Pressing this button to enter/exit the heart rate recovery function test when there is

      heart rate signal input in the stopped movement and non-set state.

      DOWN

      ---In the setting state, setting down the countdown interval, distance, calorie value

      and temperature (°C or °F) on the corresponding flashing window.

      RESET/GO

      ---In the setting state, resetting the countdown interval, distance value, calorie value

      on the corresponding flashing window.

      ---In the meter state, pressing and holding the RESET key for 3 seconds to clear all

      window display values. --In the body parameter setstate, pressing this button to start

      the body fat level.

      BODYFAT

      ---In the stopping setstate, entering/exiting the lipid measurement parameters.

      1. Meter Function

      Speed, rpm, fat percentage: Window A display

      (1) It measures the instantaneous speed, showing the speed of movement, and the measurement range is 0.0 ~ 99.9

      km/h

      (2) Revolutions per minute (RPM) measures the pedal speed, showing the speed of the treadwheel. Measurement

      range 0 ~ 1500 rpm

      (3) It measures the percentage of body fat

      Time/body mass index BMI: Window B display

      (1) Measuring the cumulative time of exercise

      Measuring the time from start doing exercise to stop, ranging from 0 to 99 minutes and 59 seconds

      (2) Time alarm function

      Firstly setting the exercise time, after the exercise starts, the time will be counted backwards, counting to zero alarm 10

      seconds, the maximum setting time is 99 minutes.

      (3) Measuring BMI value

      Distance/basal metabolic rate BMR: Window C display

      (1) Measuring the cumulative distance of motion

      Measuring the distance from the start to the stop of movement, with the measuring range of 0.00~9.99~99.9 km, it will

      automatically display with one decimal after counting 9.99 km.

      (2) Distance alarm function

      Setting the movement distance first, the time will be counted backwards after the movement starts, counting to zero

      alarm 10 seconds. The maximum setting value is 99.9 kilometers.

      (3) Measuring BMR value

      Calories/temperature: Window D display15

      (1) Measuring the accumulated heat consumption of exercise

      Measuring the heat (i.e., calories) consumed from the start to the stop of exercise, with the measuring range of

      0.0~99.9~999 kcal, it will automatically turn to integer display after counting 99.9 kcal.

      (2) Calorie alarm function

      Firstly, setting the calories consumed by exercise, after the exercise starts, the time counts down to zero, then alarming

      for 10 seconds. the maximum setting value is 999 kcal.

      (3) Measuring temperature (℃ or F)

      Heart rate: Window E display

      Measuring the number of heartbeats per minute, ranging from 40 to 240 beats per minute. If there is no heartbeat signal

      for 60 seconds, and then automatically showing the symbol "P", indicating that the heart rate test is suspended;

      Pressing the UP or DOWN key for once, if the symbol "P" changes to "□", indicating that the heart rate can be tested.

      Wheel circumference

      Setting it to a certain size according to the matching requirements of fitness equipment.

      There are key tones when operating the MODE status key, REC0VERY/UP key, DOWN key, RESET/G0 key or

      BODYFAT key.

      Standing still for 8 minutes (no key operation and no movement), the instrument will automatically shut down and

      clear all data except human body parameters and temperature, at the same time, it will automatically switches to

      display only the temperature value, and the operation button or the start of the movement will automatically display.

      Instrument installation method

      Removing the battery door on the rear housing, loading two new No.5 with 1.5 volt (size SIZEAAUM3R6) or No.7

      (size SIZEAAUM4R03) batteries according to the positive and negative directions on the battery box and the battery

      model indicated in the battery box. The meter with MP3 needs to load 4 batteries.

      Fixing the meter on the dashboard in front of the fitness equipment with silk.

      Installing the magnet base and the sensor at the designated positions of the fitness equipment, and keeping parallel,

      with the distance between them being 2~15mm and the axial separation being 7 ~ 10 mm.

      Connecting the sensor wire plug with the connector of the outgoing line on the back of the instrument or inserting it

      into the signal input jack on the back of the instrument.

      When stepping on the fitness machine, the displayed speed changes, indicating that the installation is qualified.

      Otherwise, check whether the magnet seat and the sensor are installed correctly and whether the connection between

      the sensor wire plug and the meter head lead is reliable.

      Instrument usage method

      Pressing the MODE status key to select the display window to be set or cleared, the value on the corresponding

      window flashes, pressing the UP/DOWN key to set the alarm time or alarm distance or alarm calories you need, and

      pressing and holding the UP/D0WN key without moving, which can be set quickly; Pressing the RESET key to clear

      the value displayed in the corresponding window.

      Stepping on the fitness machine to start measuring, and observing your exercise parameters according to the contents

      displayed in different windows.

      Heart rate measurement: Click the UP or DOWN key, and then grasping the metal plate of the heart rate sensor at the

      corresponding position with the left and right palms respectively

      (Note: each palm should touch two metal plates at the same time). After 3~4 seconds, the heart rate display window

      displays your current heart rate in beats/minute. When the heartbeat signal is received during the measurement, the

      heartbeat symbol "zero" flashes. In order to prevent palm movements from affecting heart rate measurement and

      ensure accurate heart rate measurement, it is suggested that heart rate measurement should be carried out after pause or

      stop, and heart umbrella should not be measured when running.16

      Tips: As signal interference sometimes occurs when the palm catches the metal sheet, the heart rate value displayed in

      the first 2-3 seconds may be inaccurate and on the high side, which is a normal phenomenon, and then the heart rate

      will return to normal measurement. Monitoring heart rate in this way is mainly helpful to determine your exercise, and

      cannot be used as a basis for disease treatment.

      Note: For an instrument equipped with a wireless heart rate receiving device for chest strap, the chest strap shall be

      properly worn first, and the heart rate signal shall be sent to the instrument within the signal range of chest strap.

      Measuring heart rate recovery ability: In the unset state after stopping exercise (speed is 0), the heart rate should be

      measured by the above heart rate measurement method, pressing REC0VERY/UP key to enter the heart rate recovery

      function test, and then keeping holding hands or wearing chest strap (when this function is available) to measure the

      heart rate. At this time, the time window displays a 1-minute countdown, and the value in the heart rate display

      window will decrease because the heartbeat gradually returns to calm after stopping exercise, When the time is counted

      down to 0, your heart rate recovery status (F1 ~ F6) will be displayed, where F1 means the fastest heart rate recovery,

      followed by fast to slow, and F6 means the slowest. Pressing the REC0VERY/UP again to exit the heart rate recovery

      function test.

      Measuring fat percentage, BMI and BMR: In the non-movement (speed is 0) state, pressing m) DYFAT key to enter the

      lipid measurement parameter setting state, first setting the individual N0. At this time, the corresponding N0. value

      flashes, pressing REC0VERY/UP key, DOWN key to select the setting (1 ~ 8) up to 8 human body data. Pressing the

      MODE key to enter the weight setting, pressing the REC0VERY/UP key or the DOWN key to set the weight value,

      and so on: Setting weight KG, height CM, age YEAR and gender in turn. Pressing RESET/G0 key after setting, then

      holding the heart rate sensing metal sheet with both hands, displaying the results after 6 seconds. Pressing B0DYFAT

      again to exit the lipid measurement state.

      Note: (1) In the human body data setting state, if there is no operation within 10 seconds, it will automatically exit the

      setting state of lipid measurement parameters

      (2) In the process of fat measurement, if the measured body is not sensed for 10 seconds, [ER.1] will be displayed.

      Comparison Table of Fat Content and Obesity

      Gender/age

      Relatively

      thin

      Normal

      Slightly fat

      Overweight

      Obesity

      Male /<30

      <14%

      14%~20%

      20.1%~25%

      25.1%~35%

      >35%

      Male /> 30

      <17%

      17%~23%

      23.1%~28%

      28.1%~38%

      >38%

      Female /<30

      <17%

      17%~24%

      24,1%~30%

      30.1%~40%

      >40%

      Female />30

      <20%

      20%~27%

      27.1%~33%

      33.1%~43%

      >43%

      1. Audio Amplification and Output [If this function is available]

      Connecting the audio input line to the output port of the audio player, and turning on the audio switch on the right side of

      this table to play the music output by the audio player.

      1. Battery Replacement

      When the display dims or there is no display, removing the battery door, install 2 new No. 5 with 1.5 V(AA, UM3) or No. 7

      (AAA, UM4) batteries (4 batteries with MP3) according to the direction of the positive and negative electrodes of the

      battery and the battery model indicated in the battery box, and install it back.Maintenance Service Description:

      User Name:

      Purchase

      Date:

      Name of

      Commodity:

      Product

      Model:

      Purchase

      Place:

      Tel.:

      Repair Date

      Failure and

      Inspection Record

      Maintenance

      Date

      Technician

      Warranty Card

      Maintenance Records

      MERACH, Global Family Fitness Expert

      1.Installation of goods shall be carried out in

      accordance with the instructions of the product

      drawings. Damage or accident caused by wrong

      installation or improper use shall not be included

      in the scope of free maintenance.

      2.If the goods need to be repaired, this card

      and purchase certifificate should be attached to

      the designated repair center for repair.

      3.Maintenance fee will be charged for items

      beyond the free range.

      Warranty Period:

      The whole machine is guaranteed free of

      charge for one year from the date of

      purchase (man-made damage is not within

      the warranty scope). Please keep the shop

      ping voucher and warranty card properly.

      Email:service@merach.com

      Offiffifficial Website: www.merach.com

      Company: Zhejiang Yulu Electronic Technology Co., Ltd.

      Address: 298 Weiye Road, Binjiang District, Hangzhou,

      Zhejiang Province, China

      REVIEWS
      BACK TO TOP